Structurix u film processor error codes full#

Check mixing procedures if needed make new fresh solution. Check replenishment pumps & settings and adjust accordingly. Check the temperature with a thermometer and adjust setting. TROUBLESHOOTING GUIDE Problem Possible Cause Action to be taken Light Image. Always read the label and product information before use! / 6Ĥ VIII.

Structurix u film processor error codes full#

For full details on the usage of Algstop LR, please ask for the separate FUJIFILM Technical Info Sheets AlgStop. Closed, recirculated wash systems In the low wash water usage and high temperature conditions resulting from recirculation of washwater, it has proven to be difficult to keep bio-growth under control. An automatic Algstop Dosing Unit is available from FUJIFILM. It is only necessary to add 1 ml of Algstop LR concentrate for each litre of wash water capacity to the wash tank at the end of a processing session. FUJIFILM Algstop LR is very effective in preventing algae growth during shutdown periods. Various biocides compatible with photographic processors are available. If problems are experienced it is best to first have an examination of the water quality and supply system, carried out by a specialist company. BIOLOGICAL GROWTH IN WASH TANK Open wash system It is not usual for biological growth to be found in well-maintained processors with open wash systems and adequate wash water flow rates (1-3 litres/minute). Normally a reduction to about 1/10 th of the normal concentration can be achieved. This has the benefit of reducing the amount of silver complex in the processor wash water effluent. If an electrolytic fixer desilvering unit is used in a continuous mode with the processor s fixer tank solution the carry-over of silver into the wash tank will be substantially reduced. FILM WASHING Ensure adequate washing of films is achieved by adhering to processor manufacturer s recommendations. Remember to carefully clean off any deposit on the cross-over mechanism otherwise scratching of the emulsion may occur. Read instructions packed with the cleaner before use to avoid damage to machine or chemical reactions. PROCESSOR TANK CLEANLINESS If the processor shows signs of dirt or crystals built up on rollers, tank or cross-overs the machine should be emptied, thoroughly washed out and then filled with FUJIFILM Unicleaner PD solution. The silver content of the processor fixing bath should be maintained at of silver/l. CONTINUOUS ELECTROLYTIC FIXER DESILVERING In order to substantially reduce the fixer replenishment rate and to reduce silver carry-over into the processor wash tank FUJIFILM recommends the use of a suitable fixer desilvering unit. F-Fix Fixer (Processor tank and replenisher) Table 2 Mixing instructions Fixer Water Part A Part B Add water to make Kit for 10x2.5L Cat# ml ml ml Kit for 2x20L Cat# L 12 L + 5,263 L L 20 L ph AND DENSITY SPECIFICATIONS Table 3 ph & Density specifications ph (25 C) Density (20 C) g/cm³ Developer ± ± Developer Replenisher ± ± Fixer 4.30 ± ± / 6ģ IV. Then top up to the overflow with Developer Replenisher. Add 20 ml of Developer Starter (Cat# ) for each litre of tank solution volume. RD-90 Developer (To fill processor developer tank) To prepare developer tank solution, fill the processor developer tank ¾ full with Developer Replenisher. RD-90 Developer Replenisher Table 1 Mixing instructions Developer Replenisher Water Part A Part B Part C Add water to make Kit for 10x2.5L Cat# ml ml + 73 ml + 62 ml 2.5 L Kit for 2x20L Cat# L + 5,526 L L L 20 L 2. It will be necessary to increase developer replenishment rates to maintain an adequate activity.Ģ III. If the processor is subject to low film usage or long periods of inactivity, aerial oxidation will occur. The machine tank size - surface to volume ratio affects aerial oxidation rate. The size of film being used - small sheets usually cause higher aerial oxidation. The operating temperature chosen - oxidation increases with temperature increase.

The amount of film processed daily - low use rates produce high oxidation rates. Replenishment rates Developer (*) Fixer Fixer (with continuous electrolytic desilvering) 400 ml/m² 600 ml/m² 300 ml/m² (*) These rates may vary depending on : 1.

Machine time cycle (sec.) Operating temperature ( C) B. Temperature RD-90 Developer and F-Fix Fixer may be utilised over a wide temperature range to suit different machine time cycles to obtain optimum results. F-Fix Fixer & Replenisher, a 2-part hardening fixer, is the companion of RD-90 Developer Replenisher. RD-90 Developer Replenisher is used to prepare both tank solution (using RD-90 Developer Starter) and replenisher solution. SYSTEM DESCRIPTION RD-90, a 3-part liquid concentrate is formulated for use in all automatic processing machines for all standard cycle times. 1 T E C H N I C A L I N F O S H E E T RD-90 Developer-Replenisher F-Fix Fixer-Replenisher I.